All you need to add is a microcontroller or other control circuit to turn the H-Bridge on and off. A pin male header and three 2-pin terminal blocks are included but not soldered onto the boards. No printed documentation is shipped with these items; please see the MC datasheet in the resources tab for more information about the motor drivers. However, the chip by itself will overheat at lower currents see table above for typical values. Each feedback FB pin outputs a voltage proportional to the H-Bridge high-side current of its associated driver, providing approximately 0.

Uploader: JoJoshura
Date Added: 24 June 2009
File Size: 53.78 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 83240
Price: Free* [*Free Regsitration Required]

All you need to add is a mc33887 motor or other control circuit to turn the H-Bridge on and off. This third capacitor can be added in conjunction with the two surface-mount capacitors to further limit disturbances on the main power line, or it can be added in place of the two surface-mount capacitors to allow the MC mc33887 motor driver carrier to function at high voltages.

MC|H-Bridge, Brushed DC Motor Driver|NXP

The fault-status FSactive low output pins may be left disconnected if you do not want to monitor the fault conditions of the motor drivers; if you do connect them you must use an external pull-up mc33887 motor to pull the lines high. Shop Blog Forum Support.

The fault-status FSactive low output pin mc33887 motor be left disconnected if you do not want to monitor the fault conditions of the motor driver; if you do connect mc33887 motor you must use an external pull-up resistor to pull the line high.

Recent Drivers  MSI 945GM3 DRIVERS DOWNLOAD

Encoder for Pololu Wheel 42x19mm. mottor

No printed documentation is shipped motoe these items; please see the MC datasheet in mc33887 motor resources tab for more mc33887 motor about the motor drivers. Shop Blog Forum Support. All you need to add is a microcontroller or other control circuit to turn the H-Bridge on and off.

Extra features such as current sensing and over-current protection make the an excellent general-purpose motor driver. This means that if you push the chip close to its limit, you will see less power to the motor, but it might allow you to avoid a complete shutdown.

notor Schematic Diagram The diagram above shows the circuit for one of the two motor drivers. MC Specifications only one active driver Operating voltage: In our tests, we were able mc33887 motor deliver 5 A for a few seconds and 2. If you have two motors to control, please consider the Dual MC motor driver carrier.

The actual current you can deliver will depend on how well mc33887 motor can keep the motor driver cool. Mc33887 motor new account Request new password.

Products New Products Specials! MC Motor Driver Carrier. mv33887

MC33887: H-Bridge, Brushed DC Motor Driver, 5-28V, 5A, 10kHz

MC Motor Mc33887 motor Carrier. Each feedback FB pin outputs mc33887 motor voltage proportional to the H-Bridge high-side current of mx33887 associated driver, providing approximately 0. However, the chip by itself will overheat at lower currents see table above for typical values. However, the chip by itself will overheat at lower currents see table above for typical values.

Recent Drivers  HP PHOTOSMART D7368 DRIVERS FOR WINDOWS 7

This board has been replaced by the more capable dual MC motor driver mc33887 motor. The feedback FB pin outputs a voltage proportional to the H-Bridge high-side current, providing approximately 0.

Print Email a friend Feeds.

The diagram above shows the circuit for one of the two motor drivers. What code is in the mc333887 However, the chip by itself will overheat at lower currents see table above for typical values. A pin male header and three 2-pin terminal mc33887 motor are included but not soldered motot the boards. Print Email a friend Feeds. The actual current you can deliver will depend on mc33887 motor well you can keep the motor driver cool. MC Specifications Operating voltage: An 8-pin male header and two 2-pin terminal blocks are included but not soldered onto the boards.

Feedback Comments or questions? This third capacitor can be added in conjunction with the two surface-mount capacitors to further limit disturbances on the main power line, or it can be added ,otor place of the two surface-mount mc33887 motor to allow the MC motor mc33887 motor carrier to function at high voltages.